文章目录
1 简介1 硬件要求2 项目背景3 实现功能4 OLDE显示屏5 IO扩展器6 系统构建7 完整代码8 最后1 简介
Hi,大家好,学长今天向大家介绍一个 单片机项目,大家可用于 课程设计 或 毕业设计
基于Arduino的智能灌溉系统
1 硬件要求
rduino NANO开发板 1块
IO扩展板 1块
IO扩展模块包 1套
开发工具
2 项目背景
使用Arduino创建智能灌溉控制器
智能灌溉您的院子或花园用动态水循环。如果正在下雨,或者自从上次浇水后就已经下雨了,不要再给院子浇水了。使用光传感器检测日出时间,并自动调整水开始时间。如果天气太冷,就停止给院子浇水。
3 实现功能
户外温度传感器户外下雨传感器户外光照传感器有电池的RTC支持按周的灌溉调度非易失性存储-永远不会因为断电而丢失灌溉设置参数日出检测智能的浇水可以节省你的水费日出前浇水,留出适当的渗透时间减少真菌生长简单的调度控制制作智能灌溉控制器所需的零件清单
IO扩展板 1块单总线转I2C 2块单线连接器 1个光纤连接器 1个光分路器 1个Arduino Nano开发板 1块4路直流5V继电器TSL2561光传感器DS18B20防水温度传感器光学红外水位传感器DS3231 AT24C32 IIC精密实时时钟I2C SSD1306 OLED 128x64显示屏透明防水塑料外壳200x120x75mm透明防水塑料外壳100x68x50mmip68 pg7防水尼龙电缆盖ip68 pg11防水尼龙电缆盖RJ11 螺钉接线端子50英尺4C4P RJ11线6" 4C4P RJ11线2.54毫米接头线2引脚SPST瞬时微动按钮开关 2个12VDC 1A适配器电源
接线图
4 OLDE显示屏
点击Menu按钮显示菜单,并继续点击此按钮循环完成所有菜单选项。如果30秒没有操作这个菜单将会自动返回。按下选择按钮以执行所需的菜单功能。
5 IO扩展器
使用io扩展器的优点如下
设计更简单现成的零件不需要编写单线驱动程序不需要编写DS3231 RTC驱动程序不需要编写EEPROM 驱动程序不需要编写OLED驱动程序没有显示字体占用Arduino代码空间不需要编写温度传感器驱动程序不需要编写光学雨感测器驱动程序节省Arduino上的代码空间;只有12710字节(39%)只要三天的时间来写代码易于电线使用标准的RJ11电话电缆无传感器电缆长度问题比类似的商业系统更便宜易于进行更改以适应个别需求单电源供电
6 系统构建
将Arduino Nano连接到IO扩展器,并使用以下代码对其进行编程。6 pin头是软件的串行调试端口,在最终的安装中是不需要的。
这里要确保更改了ONEWIRE_TO_I2C_ROM1和ONEWIRE-TO_I2C_ROM2定义的地址,使单总线地址与I2C地址相匹配。
注意:如果使用USB端口来给Arduino Nano编程,必须断开它与IO扩展器的连接,因为它也使用相同的单一串行端口,相反,如果想调试使用ICSP端口来编程ATmega328P。要启用软件调试端口,请取消对SERIAL_DEBUG定义的注释。
分配器必须首先配置为将光学红外传感器数据线与单线远程传感器线隔离。在R2处焊接零欧姆0603电阻。
将SPST轻触按钮微动开关接上RJ11螺丝端子。使用热收缩管绝缘接触端。
连接所有电线和组装/馈送所有部件到大外壳。将所有部件装到大外壳里,并连接所有导线。
用于连接远程传感器的50英尺的RJ11电缆应该刚好穿过PG11防水头,而不用剪断它。
在小外壳的顶部钻一个9/16英寸的孔,用于安装光学红外水传感器。使用达美电磨工具稍微把孔扩大一点,直到传感器安装到位。小型远程传感器与外壳紧密贴合,但是如果传感器是按照推荐的方向放置的,那么它应该刚好合适。使RJ11电缆尽可能短将有助于把它塞进更小的外壳。组装完成后,建议在拧上螺母之前在压盖螺母垫圈中添加一些防水胶,将会有更好的密封效果。
测试系统,确保一切正常。要测试继电器和传感器,请断开Arduino与IO扩展器的连接,并将其直接连接到您的计算机以手动控制它。一旦您确认一切正常,使用双面胶带和包装泡沫将所有部件组装到外壳中,以保护您的电路板,并享受智能灌溉控制器带来的好处和节约用水。
7 完整代码
使用你的Arduino智能浇灌你的院子或花园。
#include <math.h>#include <time.h> // File located \Program Files (x86)\Arduino\hardware\tools\avr\avr\include\time.h#include <util/crc16.h>#include <avr/wdt.h>#include <SoftwareSerial.h>#include "IOExpander.h"#define FAHRENHEIT#define INIT_BOARD "g5w1;g11w1;g11d0,75;g12w1;g12d0,75;rsf"#define ONEWIRE_TO_I2C_ROM1"i4scc"#define ONEWIRE_TO_I2C_ROM2"i6s8f"#define ONEWIRE_TEMPERATURE"t6s0300"#define RTC_SENSOR "s4te"#define I2C_EEPROM "s4tf"#define I2C_OLED"s4t10"#define I2C_LIGHT"s3t9;sc0"#define OPTICAL_SENSOR"g5a"#define BUTTON1 "g11d"#define BUTTON2 "g12d"#define WATER_TIME_BEFORE_SUNRISE 60#define SUNRISE_LUX 100#define RAIN_DETECT_LEVEL 4.0#define DO_NOT_WATER_TEMP 4.4444 // 40F#define MAX_ZONES4#define HOUR_IN_DAY 24L#define MIN_IN_HOUR 60L#define SEC_IN_MIN 60L#define SEC_IN_HOUR (MIN_IN_HOUR * SEC_IN_MIN)#define SEC_IN_DAY (HOUR_IN_DAY * SEC_IN_HOUR)#define DAYS_IN_WEEK 7#define SEC_IN_WEEK (SEC_IN_DAY * DAYS_IN_WEEK)#define SUN 0x01#define MON 0x02#define TUE 0x04#define WED 0x08#define THR 0x10#define FRI 0x20#define SAT 0x40#define EVERYDAY(SUN | MON | TUE | WED | THR | FRI | SAT)#define SUNRISE 0x80#define MENU_OPTIONS 9#define MENU_TIME30#define OFF 0#define ON 1#define STATE_ON_OFF 0x01//#define SERIAL_DEBUG#ifdef SERIAL_DEBUGSoftwareSerial swSerial(8,7);#endifchar weekday[][4] = {"SUN","MON","TUE","WED","THU","FRI","SAT"};char menu[][13] = {"Next","Water","Reset","Clock Min +","Clock Min -","Clock Hour +","Clock Hour -","Sunrise","ON/OFF"};enum {MENU_NEXT,MENU_WATER,MENU_RESET,MENU_CLOCK_MIN_PLUS,MENU_CLOCK_MIN_MINUS,MENU_CLOCK_HOUR_PLUS,MENU_CLOCK_HOUR_MINUS,MENU_SUNRISE,MENU_ON_OFF};typedef struct {char description[16];uint8_t relay;} ZONE;typedef struct {uint8_t zone;uint8_t days;int8_t hour;int8_t min;uint8_t duration;} SCHEDULE;typedef struct {time_t sunrise_time;time_t last_water_time;uint8_t water_schedule;uint8_t water_duration;uint8_t rain[MAX_ZONES];uint8_t state;uint8_t crc;} NVRAM;enum {ZONE1,ZONE2,ZONE3,ZONE4};enum {RELAY1 = 1,RELAY2,RELAY3,RELAY4};ZONE zone[] = {{"Front Right", RELAY1},{"Front Left", RELAY2},{"Bushes",RELAY3},{"Left Side", RELAY4},};SCHEDULE schedule[] = {{ZONE1, SUNRISE | EVERYDAY, -1, 0, 4},{ZONE2, EVERYDAY, 6, 15, 5},{ZONE3, EVERYDAY, 6, 0, 10},{ZONE4, EVERYDAY, 6, 10, 6},}; NVRAM nvram;bool update_nvram = false;uint8_t crc8(uint8_t* data, uint16_t length){uint8_t crc = 0;while (length--) {crc = _crc8_ccitt_update(crc, *data++);}return crc;}int led = 13;bool init_oled = true;bool update_oled = true;bool init_board = true;#ifdef FAHRENHEIT#define C2F(temp) CelsiusToFahrenheit(temp)float CelsiusToFahrenheit(float celsius){return ((celsius * 9) / 5) + 32;}#else#define C2F(temp) (temp)#endifvoid SerialPrint(const char* str, float decimal, char error){Serial.print(str);if (error) Serial.print(F("NA"));else Serial.print(decimal, 1);}time_t NextScheduleTime(time_t last_time, uint8_t* next_schedule){time_t next_time = -1;time_t clk_time;uint8_t i;tm clk;uint8_t wday;for (i = 0; i < sizeof(schedule) / sizeof(SCHEDULE); i++) {if (schedule[i].days & SUNRISE) {clk_time = nvram.sunrise_time; clk_time += schedule[i].hour * SEC_IN_HOUR;clk_time += schedule[i].min * SEC_IN_MIN;localtime_r(&clk_time, &clk);} else {localtime_r(&last_time, &clk);clk.tm_hour = schedule[i].hour;clk.tm_min = schedule[i].min;clk.tm_sec = 0;clk_time = mktime(&clk);}wday = clk.tm_wday;while (clk_time <= last_time || !(schedule[i].days & (1 << wday))){clk_time += SEC_IN_DAY;if (++wday > SATURDAY) wday = SUNDAY;if (wday == clk.tm_wday) break; // Only check one week}if (clk_time < next_time) {next_time = clk_time;*next_schedule = i;}}return next_time;}void StartScheduleTime(time_t start_time, uint8_t start_schedule){uint8_t i;nvram.last_water_time = start_time;nvram.water_schedule = start_schedule;nvram.water_duration = schedule[start_schedule].duration+1;update_nvram = true;// Check if it rainedi = schedule[start_schedule].zone;if (i < MAX_ZONES && nvram.rain[i] > 0) {if (nvram.rain[i] > nvram.water_duration) nvram.water_duration = 0;else nvram.water_duration -= nvram.rain[i];nvram.rain[i] = 0;}}void WaterScheduleTime(void) {uint8_t i;nvram.water_duration--;update_nvram = true;i = schedule[nvram.water_schedule].zone;if (i < MAX_ZONES) {Serial.print("r");Serial.print(zone[i].relay);if (nvram.water_duration > 0) Serial.println("o");else Serial.println("f");SerialReadUntilDone();}}void setup() {Serial.begin(115200);#ifdef SERIAL_DEBUGswSerial.begin(115200);#endif pinMode(led, OUTPUT);//delay(1000);wdt_enable(WDTO_8S);}void loop() {static tm rtc;tm clk, sunrise_clk;time_t rtc_time;time_t clk_time;static time_t next_time;static uint8_t last_sec;static uint8_t last_min;bool error_rtc;bool error_light;bool error_temp;static long lux = 0;static float temp, rain;static uint8_t sunrise_counter = MIN_IN_HOUR;static bool check_sunrise = false;uint8_t i;static bool read_nvram = true;static time_t water_time;static uint8_t water_schedule;uint8_t sz;uint8_t wday;long n;bool button1, button2;static int8_t menu_select = -1;static time_t menu_time = 0;Serial.println();if (SerialReadUntilDone()) {if (init_board) {SerialCmdDone(INIT_BOARD);init_board = false;}if (init_oled) {if (SerialCmdNoError(ONEWIRE_TO_I2C_ROM1)) {SerialCmdDone(I2C_OLED ";si;sc;sd");init_oled = false;}}if (SerialCmdDone(RTC_SENSOR)) {error_rtc = !SerialReadTime(&rtc);if (!error_rtc) {clk = rtc; // mktime() can change struct tmrtc_time = mktime(&clk);localtime_r(&rtc_time, &rtc); // Get wday.}if (read_nvram) {if (SerialCmdNoError(I2C_EEPROM)) {SerialReadEEPROM((uint8_t*)&nvram, 0, sizeof(nvram));if (nvram.crc != crc8((uint8_t*)&nvram, sizeof(nvram)-sizeof(uint8_t))) {//swSerial.println("CRC8 Failure!");// Initialize nvrammemset(&nvram, 0, sizeof(nvram));clk = rtc;clk.tm_hour = 6;clk.tm_min = 0;clk.tm_sec = 0;nvram.sunrise_time = mktime(&clk);if (nvram.sunrise_time < rtc_time) nvram.sunrise_time + SEC_IN_DAY;update_nvram = true;}// Check last water time no less than one weekif (rtc_time - nvram.last_water_time > SEC_IN_WEEK) nvram.last_water_time = rtc_time - SEC_IN_WEEK;// Check sunrise timeif (rtc_time > nvram.sunrise_time) {localtime_r(&nvram.sunrise_time, &sunrise_clk);clk = rtc;clk.tm_hour = sunrise_clk.tm_hour;clk.tm_min = sunrise_clk.tm_min;clk.tm_sec = sunrise_clk.tm_sec;nvram.sunrise_time = mktime(&clk);if (nvram.sunrise_time < rtc_time) nvram.sunrise_time + SEC_IN_DAY; }if (nvram.water_duration) {nvram.water_duration++;water_time = nvram.last_water_time;}else {clk_time = (nvram.last_water_time) ? nvram.last_water_time : rtc_time;water_time = NextScheduleTime(clk_time, &water_schedule);}read_nvram = false;}}}// Process only once every minuteif (rtc.tm_min != last_min){// Request a 1-Wire temperature measurement. Read it later.error_temp = !SerialCmdNoError(ONEWIRE_TEMPERATURE);if (!error_temp) SerialCmdDone("tt");error_light = !SerialCmdNoError(ONEWIRE_TO_I2C_ROM2 ";oo0");if (!error_light) {SerialCmdDone(I2C_LIGHT); // Do not use overdriveSerialCmd("sr");SerialReadInt(&lux);SerialReadUntilDone();}if (SerialCmd(OPTICAL_SENSOR)) {SerialReadFloat(&rain);SerialReadUntilDone();}error_temp = !SerialCmdNoError(ONEWIRE_TEMPERATURE);if (!error_temp) {SerialCmd("tr");SerialReadFloat(&temp);SerialReadUntilDone();}// Is it sunrise?if (lux < SUNRISE_LUX) {if (sunrise_counter > 0) sunrise_counter--;else check_sunrise = true;}else {if (sunrise_counter < MIN_IN_HOUR) {sunrise_counter++;if (check_sunrise && sunrise_counter == MIN_IN_HOUR) {nvram.sunrise_time = rtc_time + (SEC_IN_DAY - SEC_IN_HOUR);check_sunrise = false;update_nvram = true;}}}// Is it raining?if (rain <= RAIN_DETECT_LEVEL) {for (i = 0; i < MAX_ZONES; i++) {if (nvram.rain[i] < -1) nvram.rain[i]++;}update_nvram = true;}// Check scheduleif (menu_select == -1 && !nvram.water_duration) {while (water_time + (schedule[water_schedule].duration * SEC_IN_MIN) < rtc_time) {water_time = NextScheduleTime(water_time, &water_schedule);}if (water_time <= rtc_time) {StartScheduleTime(water_time, water_schedule);if (temp <= DO_NOT_WATER_TEMP || nvram.state & STATE_ON_OFF == OFF)nvram.water_duration = 0;}}// Do we need to water?if (nvram.water_duration) {WaterScheduleTime();if (!nvram.water_duration)water_time = NextScheduleTime(water_time, &water_schedule);}last_min = rtc.tm_min;update_oled = true;}// Check buttonsbutton1 = SerialReadButton(BUTTON1);if (button1) {if (menu_select == -1) menu_select = 0;else {if (++menu_select >= MENU_OPTIONS)menu_select = 0;}menu_time = rtc_time;update_oled = true;}if (menu_select >= 0) {button2 = SerialReadButton(BUTTON2);if (button2) {clk_time = rtc_time;switch(menu_select) {case MENU_NEXT:case MENU_RESET:if (nvram.water_duration) {nvram.water_duration = 1;WaterScheduleTime();}water_time = NextScheduleTime((menu_select == MENU_NEXT) ? water_time : rtc_time, &water_schedule);break;case MENU_WATER:StartScheduleTime(water_time, water_schedule);WaterScheduleTime();break;case MENU_CLOCK_MIN_PLUS:clk_time += SEC_IN_MIN;break;case MENU_CLOCK_MIN_MINUS:clk_time -= SEC_IN_MIN;break;case MENU_CLOCK_HOUR_PLUS:clk_time += SEC_IN_HOUR;break;case MENU_CLOCK_HOUR_MINUS:clk_time -= SEC_IN_HOUR;break;case MENU_ON_OFF:nvram.state ^= STATE_ON_OFF;update_nvram = true;break; }if (clk_time != rtc_time) {if (SerialCmdDone(RTC_SENSOR)) {localtime_r(&clk_time, &clk);SerialWriteTime(&clk);rtc_time = clk_time;}}menu_time = rtc_time;update_oled = true;}}if (menu_select >= 0 && rtc_time - menu_time > MENU_TIME) {menu_select = -1;update_oled = true;}if (update_oled) {if (SerialCmdNoError(ONEWIRE_TO_I2C_ROM1)) {Serial.print("st10;so1;sc;sf0;sa0;sd0,0,\"");if (nvram.water_duration) Serial.print(nvram.water_duration);else {if ((nvram.state & STATE_ON_OFF) == OFF) Serial.print("OFF");else if (rain <= RAIN_DETECT_LEVEL) Serial.print("Rain");else if (temp <= DO_NOT_WATER_TEMP) Serial.print("Cold");else Serial.print("v1.1");}Serial.print("\";sf2;sa1;sd75,0,\"");if (menu_select == 7) {// Sunriseclk_time = nvram.sunrise_time;localtime_r(&clk_time, &clk);}else clk = rtc;Serial.print(clk.tm_hour-((clk.tm_hour>12)?12:0));Serial.print(":");if (clk.tm_min < 10) Serial.print("0");Serial.print(clk.tm_min);Serial.println("\"");SerialReadUntilDone();Serial.print("sf1;sa0;sd79,8,\"");Serial.print((clk.tm_hour>12)?"PM":"AM");Serial.print("\";sf0;sa1;sd127,1,\"");Serial.print(weekday[clk.tm_wday]);Serial.print("\";sd127,13,\"");Serial.print(clk.tm_mon+1);Serial.print("/");Serial.print(clk.tm_mday);Serial.println("\"");SerialReadUntilDone();Serial.print("sf0;sa0;sd1,36,\"");i = schedule[water_schedule].zone;if (i < MAX_ZONES) Serial.print(zone[i].description);localtime_r(&water_time, &clk);if (water_time - rtc_time > SEC_IN_DAY) {Serial.print("\";sa1;sd126,36,\"");Serial.print(clk.tm_mon+1);Serial.print("/");Serial.print(clk.tm_mday);Serial.print(" ");Serial.print(clk.tm_hour-((clk.tm_hour>12)?12:0));Serial.print(":");if (clk.tm_min < 10) Serial.print("0");Serial.print(clk.tm_min); Serial.print(" ");}else {Serial.print("\";sf1;sa1;sd111,30,\"");Serial.print(clk.tm_hour-((clk.tm_hour>12)?12:0));Serial.print(":");if (clk.tm_min < 10) Serial.print("0");Serial.print(clk.tm_min); Serial.print("\";sf0;sd126,36,\"");}Serial.print((clk.tm_hour>12)?"PM":"AM");if (nvram.water_duration) Serial.print("\";so2;sc0,29,128,19");Serial.println();SerialReadUntilDone();if (menu_select == -1) {//Serial.print("\";sa0;sd0,52,\"");//Serial.print(rain);SerialPrint("\";so1;sa2;sd63,52,\"", C2F(temp), error_temp);if (!error_temp) Serial.print("\",248,\""#ifdef FAHRENHEIT"F"#else"C"#endif);Serial.print(" / "); Serial.print(lux); }else {Serial.print("\";so0;sc0,51,128,14;sf0;sa2;sd63,52,\"");if (menu_select == MENU_ON_OFF) {Serial.print((nvram.state & STATE_ON_OFF) ? "OFF" : "ON");}else Serial.print(menu[menu_select]);}Serial.println("\";sd");SerialReadUntilDone();update_oled = false;}else init_oled = true;}if (update_nvram) {if (SerialCmdNoError(I2C_EEPROM)) {nvram.crc = crc8((uint8_t*)&nvram, sizeof(nvram)-sizeof(uint8_t));//swSerial.println(nvram.crc, HEX);SerialWriteEEPROM((uint8_t*)&nvram, 0, sizeof(nvram));update_nvram = false;}}delay(50);}else {digitalWrite(led, HIGH);delay(500);digitalWrite(led, LOW);delay(500);init_board = true;init_oled = true;}wdt_reset();}