之前的文章介绍了LVS负载均衡-基础知识梳理, 下面记录下LVS+Keepalived高可用环境部署梳理（主主和主从模式）的操作流程:
一、LVS+Keepalived主从热备的高可用环境部署
1）环境准备
LVS_Keepalived_Master182.148.15.237LVS_Keepalived_Backup182.148.15.236Real_Server1182.148.15.233Real_Server2182.148.15.238VIP 182.148.15.239系统版本都是centos6.8特别注意：Director Server与Real Server必须有一块网卡连在同一物理网段上！否则lvs会转发失败！在远程telnet vip port会报错："telnet: connect to address *.*.*.*: No route to host"
基本的网络拓扑图如下：
2）LVS_keepalived_Master和LVS_keepalived_Backup两台服务器上安装配置LVS和keepalived的操作记录：
1）关闭 SElinux、配置防火墙（在LVS_Keepalived_Master 和 LVS_Keepalived_Backup两台机器上都要操作）[root@LVS_Keepalived_Master ~]# vim /etc/sysconfig/selinux#SELINUX=enforcing#注释掉#SELINUXTYPE=targeted #注释掉SELINUX=disabled #增加[root@LVS_Keepalived_Master ~]# setenforce 0#临时关闭selinux。上面文件配置后，重启机器后就永久生效。注意下面182.148.15.0/24是服务器的公网网段，192.168.1.0/24是服务器的私网网段一定要注意：加上这个组播规则后，MASTER和BACKUP故障时，才能实现VIP资源的正常转移。其故障恢复后，VIP也还会正常转移回来。[root@LVS_Keepalived_Master ~]# vim /etc/sysconfig/iptables .......-A INPUT -s 182.148.15.0/24 -d 224.0.0.18 -j ACCEPT#允许组播地址通信。-A INPUT -s 192.168.1.0/24 -d 224.0.0.18 -j ACCEPT-A INPUT -s 182.148.15.0/24 -p vrrp -j ACCEPT #允许 VRRP（虚拟路由器冗余协）通信-A INPUT -s 192.168.1.0/24 -p vrrp -j ACCEPT-A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT[root@LVS_Keepalived_Master ~]# /etc/init.d/iptables restart----------------------------------------------------------------------------------------------------------------------2）LVS安装（在LVS_Keepalived_Master 和 LVS_Keepalived_Backup两台机器上都要操作）需要安装以下软件包[root@LVS_Keepalived_Master ~]# yum install -y libnl* popt*查看是否加载lvs模块[root@LVS_Keepalived_Master src]# modprobe -l |grep ipvs下载并安装LVS[root@LVS_Keepalived_Master ~]# cd /usr/local/src/[root@LVS_Keepalived_Master src]# wget /software/kernel-2.6/ipvsadm-1.26.tar.gz解压安装[root@LVS_Keepalived_Master src]# ln -s /usr/src/kernels/2.6.32-431.5.1.el6.x86_64/ /usr/src/linux[root@LVS_Keepalived_Master src]# tar -zxvf ipvsadm-1.26.tar.gz[root@LVS_Keepalived_Master src]# cd ipvsadm-1.26[root@LVS_Keepalived_Master ipvsadm-1.26]# make && make installLVS安装完成，查看当前LVS集群[root@LVS_Keepalived_Master ipvsadm-1.26]# ipvsadm -L -nIP Virtual Server version 1.2.1 (size=4096)Prot LocalAddress:Port Scheduler Flags-> RemoteAddress:Port Forward Weight ActiveConn InActConn----------------------------------------------------------------------------------------------------------------------3）编写LVS启动脚本/etc/init.d/realserver（在Real_Server1 和Real_Server2上都要操作，realserver脚本内容是一样的）[root@Real_Server1 ~]# vim /etc/init.d/realserver#!/bin/shVIP=182.148.15.239. /etc/rc.d/init.d/functionscase "$1" in# 禁用本地的ARP请求、绑定本地回环地址start)/sbin/ifconfig lo down/sbin/ifconfig lo upecho "1" >/proc/sys/net/ipv4/conf/lo/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/lo/arp_announceecho "1" >/proc/sys/net/ipv4/conf/all/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/all/arp_announce/sbin/sysctl -p >/dev/null 2>&1/sbin/ifconfig lo:0 $VIP netmask 255.255.255.255 up#在回环地址上绑定VIP，设定掩码，与Direct Server（自身）上的IP保持通信/sbin/route add -host $VIP dev lo:0echo "LVS-DR real server starts successfully.\n";;stop)/sbin/ifconfig lo:0 down/sbin/route del $VIP >/dev/null 2>&1echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/lo/arp_announceecho "1" >/proc/sys/net/ipv4/conf/all/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/all/arp_announceecho "LVS-DR real server stopped.\n";;status)isLoOn=`/sbin/ifconfig lo:0 | grep "$VIP"`isRoOn=`/bin/netstat -rn | grep "$VIP"`if [ "$isLoON" == "" -a "$isRoOn" == "" ]; thenecho "LVS-DR real server has run yet."elseecho "LVS-DR real server is running."fiexit 3;;*)echo "Usage: $0 {start|stop|status}"exit 1esacexit 0将lvs脚本加入开机自启动[root@Real_Server1 ~]# chmod +x /etc/init.d/realserver[root@Real_Server1 ~]# echo "/etc/init.d/realserver start" >> /etc/rc.d/rc.local启动LVS脚本(注意：如果这两台realserver机器重启了，一定要确保service realserver start 启动了，即lo:0本地回环上绑定了vip地址，否则lvs转发失败！)[root@Real_Server1 ~]# service realserver startLVS-DR real server starts successfully.\n查看Real_Server1服务器，发现VIP已经成功绑定到本地回环口lo上了[root@Real_Server1 ~]# ifconfigeth0Link encap:Ethernet HWaddr 52:54:00:D1:27:75inet addr:182.148.15.233 Bcast:182.148.15.255 Mask:255.255.255.224inet6 addr: fe80::5054:ff:fed1:2775/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:309741 errors:0 dropped:0 overruns:0 frame:0TX packets:27993954 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000RX bytes:37897512 (36.1 MiB) TX bytes:23438654329 (21.8 GiB)lo Link encap:Local Loopbackinet addr:127.0.0.1 Mask:255.0.0.0inet6 addr: ::1/128 Scope:HostUP LOOPBACK RUNNING MTU:65536 Metric:1RX packets:0 errors:0 dropped:0 overruns:0 frame:0TX packets:0 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:0RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)lo:0Link encap:Local Loopbackinet addr:182.148.15.239 Mask:255.255.255.255UP LOOPBACK RUNNING MTU:65536 Metric:1----------------------------------------------------------------------------------------------------------------------4）安装Keepalived（LVS_Keepalived_Master 和 LVS_Keepalived_Backup两台机器都要操作）[root@LVS_Keepalived_Master ~]# yum install -y openssl-devel[root@LVS_Keepalived_Master ~]# cd /usr/local/src/[root@LVS_Keepalived_Master src]# wget /software/keepalived-1.3.5.tar.gz[root@LVS_Keepalived_Master src]# tar -zvxf keepalived-1.3.5.tar.gz[root@LVS_Keepalived_Master src]# cd keepalived-1.3.5[root@LVS_Keepalived_Master keepalived-1.3.5]# ./configure --prefix=/usr/local/keepalived[root@LVS_Keepalived_Master keepalived-1.3.5]# make && make install[root@LVS_Keepalived_Master keepalived-1.3.5]# cp /usr/local/src/keepalived-1.3.5/keepalived/etc/init.d/keepalived /etc/rc.d/init.d/[root@LVS_Keepalived_Master keepalived-1.3.5]# cp /usr/local/keepalived/etc/sysconfig/keepalived /etc/sysconfig/[root@LVS_Keepalived_Master keepalived-1.3.5]# mkdir /etc/keepalived/[root@LVS_Keepalived_Master keepalived-1.3.5]# cp /usr/local/keepalived/etc/keepalived/keepalived.conf /etc/keepalived/[root@LVS_Keepalived_Master keepalived-1.3.5]# cp /usr/local/keepalived/sbin/keepalived /usr/sbin/[root@LVS_Keepalived_Master keepalived-1.3.5]# echo "/etc/init.d/keepalived start" >> /etc/rc.local[root@LVS_Keepalived_Master keepalived-1.3.5]# chmod +x /etc/rc.d/init.d/keepalived#添加执行权限[root@LVS_Keepalived_Master keepalived-1.3.5]# chkconfig keepalived on #设置开机启动[root@LVS_Keepalived_Master keepalived-1.3.5]# service keepalived start #启动[root@LVS_Keepalived_Master keepalived-1.3.5]# service keepalived stop#关闭[root@LVS_Keepalived_Master keepalived-1.3.5]# service keepalived restart #重启----------------------------------------------------------------------------------------------------------------------5）接着配置LVS+Keepalived配置现在LVS_Keepalived_Master和LVS_Keepalived_Backup两台机器上打开ip_forward转发功能[root@LVS_Keepalived_Master ~]# echo "1" > /proc/sys/net/ipv4/ip_forwardLVS_Keepalived_Master机器上的keepalived.conf配置：[root@LVS_Keepalived_Master ~]# vim /etc/keepalived/keepalived.conf! Configuration File for keepalivedglobal_defs {router_id LVS_Master}vrrp_instance VI_1 {state MASTER#指定instance初始状态，实际根据优先级决定.backup节点不一样interface eth0 #虚拟IP所在网virtual_router_id 51 #VRID，相同VRID为一个组，决定多播MAC地址priority 100#优先级，另一台改为90.backup节点不一样advert_int 1#检查间隔authentication {auth_type PASS #认证方式，可以是pass或haauth_pass 1111 #认证密码}virtual_ipaddress {182.148.15.239 #VIP}}virtual_server 182.148.15.239 80 {delay_loop 6#服务轮询的时间间隔lb_algo wrr#加权轮询调度，LVS调度算法 rr|wrr|lc|wlc|lblc|sh|shlb_kind DR #LVS集群模式 NAT|DR|TUN，其中DR模式要求负载均衡器网卡必须有一块与物理网卡在同一个网段#nat_mask 255.255.255.0persistence_timeout 50#会话保持时间protocol TCP #健康检查协议## Real Server设置，80就是连接端口real_server 182.148.15.233 80 {weight 3 ##权重TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 182.148.15.238 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}启动keepalived[root@LVS_Keepalived_Master ~]# /etc/init.d/keepalived startStarting keepalived: [ OK ][root@LVS_Keepalived_Master ~]# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWNlink/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host loinet6 ::1/128 scope hostvalid_lft forever preferred_lft forever2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 52:54:00:68:dc:b6 brd ff:ff:ff:ff:ff:ffinet 182.48.115.237/27 brd 182.48.115.255 scope global eth0inet 182.48.115.239/32 scope global eth0inet6 fe80::5054:ff:fe68:dcb6/64 scope linkvalid_lft forever preferred_lft forever注意此时网卡的变化，可以看到虚拟网卡已经分配到了realserver上。此时查看LVS集群状态，可以看到集群下有两个Real Server，调度算法，权重等信息。ActiveConn代表当前Real Server的活跃连接数。[root@LVS_Keepalived_Master ~]# ipvsadm -lnIP Virtual Server version 1.2.1 (size=4096)Prot LocalAddress:Port Scheduler Flags-> RemoteAddress:Port Forward Weight ActiveConn InActConnTCP 182.48.115.239:80 wrr persistent 50-> 182.48.115.233:80 Route 300 -> 182.48.115.238:80 Route 300 -------------------------------------------------------------------------LVS_Keepalived_Backup机器上的keepalived.conf配置：[root@LVS_Keepalived_Backup ~]# vim /etc/keepalived/keepalived.conf! Configuration File for keepalivedglobal_defs {router_id LVS_Backup}vrrp_instance VI_1 {state BACKUP interface eth0virtual_router_id 51 priority 90 advert_int 1 authentication {auth_type PASSauth_pass 1111}virtual_ipaddress {182.148.15.239}}virtual_server 182.148.15.239 80 {delay_loop 6 lb_algo wrr lb_kind DR persistence_timeout 50 protocol TCPreal_server 182.148.15.233 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 182.148.15.238 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}[root@LVS_Keepalived_Backup ~]# /etc/init.d/keepalived startStarting keepalived: [ OK ]查看LVS_Keepalived_Backup机器上，发现VIP默认在LVS_Keepalived_Master机器上，只要当LVS_Keepalived_Backup发生故障时，VIP资源才会飘到自己这边来。[root@LVS_Keepalived_Backup ~]# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWNlink/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host loinet6 ::1/128 scope hostvalid_lft forever preferred_lft forever2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 52:54:00:7c:b8:f0 brd ff:ff:ff:ff:ff:ffinet 182.48.115.236/27 brd 182.48.115.255 scope global eth0inet 182.48.115.239/27 brd 182.48.115.255 scope global secondary eth0:0inet6 fe80::5054:ff:fe7c:b8f0/64 scope linkvalid_lft forever preferred_lft forever[root@LVS_Keepalived_Backup ~]# ipvsadm -L -nIP Virtual Server version 1.2.1 (size=4096)Prot LocalAddress:Port Scheduler Flags-> RemoteAddress:Port Forward Weight ActiveConn InActConnTCP 182.48.115.239:80 wrr persistent 50-> 182.48.115.233:80 Route 300 -> 182.48.115.238:80 Route 300
3）后端两台Real Server上的操作
在两台Real Server上配置好nginx，nginx安装配置过程省略。分别在两台Real Server上配置两个域名和。在LVS_Keepalived_Master 和 LVS_Keepalived_Backup两台机器上要能正常访问这两个域名[root@LVS_Keepalived_Master ~]# curl this is page of Real_Server1:182.148.15.238 [root@LVS_Keepalived_Master ~]# curl this is page of Real_Server2:182.148.15.238 [root@LVS_Keepalived_Backup ~]# curl this is page of Real_Server1:182.148.15.238 [root@LVS_Keepalived_Backup ~]# curl this is page of Real_Server2:182.148.15.238 关闭182.148.15.238这台机器（即Real_Server2）的nginx，发现对应域名的请求就会到Real_Server1上[root@Real_Server2 ~]# /usr/local/nginx/sbin/nginx -s stop[root@Real_Server2 ~]# lsof -i:80[root@Real_Server2 ~]# 再次在LVS_Keepalived_Master 和 LVS_Keepalived_Backup两台机器上访问这两个域名，就会发现已经负载到Real_Server1上了[root@LVS_Keepalived_Master ~]# curl this is page of Real_Server1:182.148.15.233 [root@LVS_Keepalived_Master ~]# curl this is page of Real_Server1:182.148.15.233 [root@LVS_Keepalived_Backup ~]# curl this is page of Real_Server1:182.148.15.233 [root@LVS_Keepalived_Backup ~]# curl this is page of Real_Server1:182.148.15.233 另外，设置这两台Real Server的iptables，让其80端口只对前面的两个vip资源开放[root@Real_Server1 ~]# vim /etc/sysconfig/iptables......-A INPUT -s 182.148.15.239 -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT[root@Real_Server1 ~]# /etc/init.d/iptables restart
4）测试
将和测试域名解析到VIP：182.148.15.239，然后在浏览器里是可以正常访问的。
1）测试LVS功能（上面Keepalived的lvs配置中，自带了健康检查，当后端服务器的故障出现故障后会自动从lvs集群中踢出，当故障恢复后，再自动加入到集群中）先查看当前LVS集群，如下：发现后端两台Real Server的80端口都运行正常[root@LVS_Keepalived_Master ~]# ipvsadm -L -nIP Virtual Server version 1.2.1 (size=4096)Prot LocalAddress:Port Scheduler Flags-> RemoteAddress:Port Forward Weight ActiveConn InActConnTCP 182.148.15.239:80 wrr persistent 50-> 182.148.15.233:80 Route 300 -> 182.148.15.238:80 Route 300现在测试关闭一台Real Server,比如Real_Server2[root@Real_Server2 ~]# /usr/local/nginx/sbin/nginx -s stop过一会儿再次查看当前LVS集群，如下：发现Real_Server2已经被踢出当前LVS集群了[root@LVS_Keepalived_Master ~]# ipvsadm -L -nIP Virtual Server version 1.2.1 (size=4096)Prot LocalAddress:Port Scheduler Flags-> RemoteAddress:Port Forward Weight ActiveConn InActConnTCP 182.148.15.239:80 wrr persistent 50-> 182.148.15.233:80 Route 300最后重启Real_Server2的80端口，发现LVS集群里又再次将其添加进来了[root@Real_Server2 ~]# /usr/local/nginx/sbin/nginx[root@LVS_Keepalived_Master ~]# ipvsadm -L -nIP Virtual Server version 1.2.1 (size=4096)Prot LocalAddress:Port Scheduler Flags-> RemoteAddress:Port Forward Weight ActiveConn InActConnTCP 182.148.15.239:80 wrr persistent 50-> 182.148.15.233:80 Route 300 -> 182.148.15.238:80 Route 300 以上测试中，和域名访问都不受影响。2）测试Keepalived心跳测试的高可用默认情况下，VIP资源是在LVS_Keepalived_Master上[root@LVS_Keepalived_Master ~]# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWNlink/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host loinet6 ::1/128 scope hostvalid_lft forever preferred_lft forever2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 52:54:00:68:dc:b6 brd ff:ff:ff:ff:ff:ffinet 182.148.15.237/27 brd 182.148.15.255 scope global eth0inet 182.148.15.239/32 scope global eth0inet 182.148.15.239/27 brd 182.148.15.255 scope global secondary eth0:0inet6 fe80::5054:ff:fe68:dcb6/64 scope linkvalid_lft forever preferred_lft forever然后关闭LVS_Keepalived_Master的keepalived，发现VIP就会转移到LVS_Keepalived_Backup上。[root@LVS_Keepalived_Master ~]# /etc/init.d/keepalived stopStopping keepalived: [ OK ][root@LVS_Keepalived_Master ~]# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWNlink/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host loinet6 ::1/128 scope hostvalid_lft forever preferred_lft forever2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 52:54:00:68:dc:b6 brd ff:ff:ff:ff:ff:ffinet 182.148.15.237/27 brd 182.148.15.255 scope global eth0inet 182.148.15.239/27 brd 182.148.15.255 scope global secondary eth0:0inet6 fe80::5054:ff:fe68:dcb6/64 scope linkvalid_lft forever preferred_lft forever查看系统日志，能查看到LVS_Keepalived_Master的VIP的移动信息[root@LVS_Keepalived_Master ~]# tail -f /var/log/messages.............May 8 10:19:36 Haproxy_Keepalived_Master Keepalived_healthcheckers[20875]: TCP connection to [182.148.15.233]:80 failed.May 8 10:19:39 Haproxy_Keepalived_Master Keepalived_healthcheckers[20875]: TCP connection to [182.148.15.233]:80 failed.May 8 10:19:39 Haproxy_Keepalived_Master Keepalived_healthcheckers[20875]: Check on service [182.148.15.233]:80 failed after 1 retry.May 8 10:19:39 Haproxy_Keepalived_Master Keepalived_healthcheckers[20875]: Removing service [182.148.15.233]:80 from VS [182.148.15.239]:80[root@LVS_Keepalived_Backup ~]# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWNlink/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host loinet6 ::1/128 scope hostvalid_lft forever preferred_lft forever2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 52:54:00:7c:b8:f0 brd ff:ff:ff:ff:ff:ffinet 182.148.15.236/27 brd 182.148.15.255 scope global eth0inet 182.148.15.239/32 scope global eth0inet 182.148.15.239/27 brd 182.148.15.255 scope global secondary eth0:0inet6 fe80::5054:ff:fe7c:b8f0/64 scope linkvalid_lft forever preferred_lft forever接着再重新启动LVS_Keepalived_Master的keepalived，发现VIP又转移回来了[root@LVS_Keepalived_Master ~]# /etc/init.d/keepalived startStarting keepalived: [ OK ][root@LVS_Keepalived_Master ~]# ip addr1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWNlink/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host loinet6 ::1/128 scope hostvalid_lft forever preferred_lft forever2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 52:54:00:68:dc:b6 brd ff:ff:ff:ff:ff:ffinet 182.148.15.237/27 brd 182.148.15.255 scope global eth0inet 182.148.15.239/32 scope global eth0inet 182.148.15.239/27 brd 182.148.15.255 scope global secondary eth0:0inet6 fe80::5054:ff:fe68:dcb6/64 scope linkvalid_lft forever preferred_lft forever查看系统日志，能查看到LVS_Keepalived_Master的VIP转移回来的信息[root@LVS_Keepalived_Master ~]# tail -f /var/log/messages.............May 8 10:23:12 Haproxy_Keepalived_Master Keepalived_vrrp[5863]: Sending gratuitous ARP on eth0 for 182.148.15.239May 8 10:23:12 Haproxy_Keepalived_Master Keepalived_vrrp[5863]: VRRP_Instance(VI_1) Sending/queueing gratuitous ARPs on eth0 for 182.148.15.239May 8 10:23:12 Haproxy_Keepalived_Master Keepalived_vrrp[5863]: Sending gratuitous ARP on eth0 for 182.148.15.239May 8 10:23:12 Haproxy_Keepalived_Master Keepalived_vrrp[5863]: Sending gratuitous ARP on eth0 for 182.148.15.239May 8 10:23:12 Haproxy_Keepalived_Master Keepalived_vrrp[5863]: Sending gratuitous ARP on eth0 for 182.148.15.239May 8 10:23:12 Haproxy_Keepalived_Master Keepalived_vrrp[5863]: Sending gratuitous ARP on eth0 for 182.148.15.239
二、LVS+Keepalived主主热备的高可用环境部署
主主环境相比于主从环境，区别只在于：1）LVS负载均衡层需要两个VIP。比如182.148.15.239和182.148.15.235 2）后端的realserver上要绑定这两个VIP到lo本地回环口上3）Keepalived.conf的配置相比于上面的主从模式也有所不同主主架构的具体配置如下：1）编写LVS启动脚本（在Real_Server1 和Real_Server2上都要操作，realserver脚本内容是一样的）由于后端realserver机器要绑定两个VIP到本地回环口lo上（分别绑定到lo:0和lo:1），所以需要编写两个启动脚本[root@Real_Server1 ~]# vim /etc/init.d/realserver1#!/bin/shVIP=182.148.15.239. /etc/rc.d/init.d/functionscase "$1" instart)/sbin/ifconfig lo down/sbin/ifconfig lo upecho "1" >/proc/sys/net/ipv4/conf/lo/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/lo/arp_announceecho "1" >/proc/sys/net/ipv4/conf/all/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/all/arp_announce/sbin/sysctl -p >/dev/null 2>&1/sbin/ifconfig lo:0 $VIP netmask 255.255.255.255 up /sbin/route add -host $VIP dev lo:0echo "LVS-DR real server starts successfully.\n";;stop)/sbin/ifconfig lo:0 down/sbin/route del $VIP >/dev/null 2>&1echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/lo/arp_announceecho "1" >/proc/sys/net/ipv4/conf/all/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/all/arp_announceecho "LVS-DR real server stopped.\n";;status)isLoOn=`/sbin/ifconfig lo:0 | grep "$VIP"`isRoOn=`/bin/netstat -rn | grep "$VIP"`if [ "$isLoON" == "" -a "$isRoOn" == "" ]; thenecho "LVS-DR real server has run yet."elseecho "LVS-DR real server is running."fiexit 3;;*)echo "Usage: $0 {start|stop|status}"exit 1esacexit 0[root@Real_Server1 ~]# vim /etc/init.d/realserver2#!/bin/shVIP=182.148.15.235. /etc/rc.d/init.d/functionscase "$1" instart)/sbin/ifconfig lo down/sbin/ifconfig lo upecho "1" >/proc/sys/net/ipv4/conf/lo/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/lo/arp_announceecho "1" >/proc/sys/net/ipv4/conf/all/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/all/arp_announce/sbin/sysctl -p >/dev/null 2>&1/sbin/ifconfig lo:1 $VIP netmask 255.255.255.255 up /sbin/route add -host $VIP dev lo:1echo "LVS-DR real server starts successfully.\n";;stop)/sbin/ifconfig lo:1 down/sbin/route del $VIP >/dev/null 2>&1echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/lo/arp_announceecho "1" >/proc/sys/net/ipv4/conf/all/arp_ignoreecho "2" >/proc/sys/net/ipv4/conf/all/arp_announceecho "LVS-DR real server stopped.\n";;status)isLoOn=`/sbin/ifconfig lo:1 | grep "$VIP"`isRoOn=`/bin/netstat -rn | grep "$VIP"`if [ "$isLoON" == "" -a "$isRoOn" == "" ]; thenecho "LVS-DR real server has run yet."elseecho "LVS-DR real server is running."fiexit 3;;*)echo "Usage: $0 {start|stop|status}"exit 1esacexit 0将lvs脚本加入开机自启动[root@Real_Server1 ~]# chmod +x /etc/init.d/realserver1[root@Real_Server1 ~]# chmod +x /etc/init.d/realserver2[root@Real_Server1 ~]# echo "/etc/init.d/realserver1" >> /etc/rc.d/rc.local[root@Real_Server1 ~]# echo "/etc/init.d/realserver2" >> /etc/rc.d/rc.local启动LVS脚本[root@Real_Server1 ~]# service realserver1 startLVS-DR real server starts successfully.\n[root@Real_Server1 ~]# service realserver2 startLVS-DR real server starts successfully.\n查看Real_Server1服务器，发现VIP已经成功绑定到本地回环口lo上了[root@Real_Server1 ~]# ifconfigeth0Link encap:Ethernet HWaddr 52:54:00:D1:27:75inet addr:182.148.15.233 Bcast:182.148.15.255 Mask:255.255.255.224inet6 addr: fe80::5054:ff:fed1:2775/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:309741 errors:0 dropped:0 overruns:0 frame:0TX packets:27993954 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000RX bytes:37897512 (36.1 MiB) TX bytes:23438654329 (21.8 GiB)lo Link encap:Local Loopbackinet addr:127.0.0.1 Mask:255.0.0.0inet6 addr: ::1/128 Scope:HostUP LOOPBACK RUNNING MTU:65536 Metric:1RX packets:0 errors:0 dropped:0 overruns:0 frame:0TX packets:0 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:0RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)lo:0Link encap:Local Loopbackinet addr:182.148.15.239 Mask:255.255.255.255UP LOOPBACK RUNNING MTU:65536 Metric:1lo:1Link encap:Local Loopbackinet addr:182.148.15.235 Mask:255.255.255.255UP LOOPBACK RUNNING MTU:65536 Metric:12）Keepalived.conf的配置 LVS_Keepalived_Master机器上的Keepalived.conf配置先打开ip_forward路由转发功能[root@LVS_Keepalived_Master ~]# echo "1" > /proc/sys/net/ipv4/ip_forward[root@LVS_Keepalived_Master ~]# vim /etc/keepalived/keepalived.conf! Configuration File for keepalivedglobal_defs {router_id LVS_Master}vrrp_instance VI_1 {state MASTER interface eth0 virtual_router_id 51priority 100 advert_int 1 authentication {auth_type PASS auth_pass 1111 }virtual_ipaddress {182.148.15.239 }}vrrp_instance VI_2 {state BACKUP interface eth0virtual_router_id 52 priority 90 advert_int 1 authentication {auth_type PASSauth_pass 1111}virtual_ipaddress {182.148.15.235 }}virtual_server 182.148.15.239 80 {delay_loop 6 lb_algo wrrlb_kind DR#nat_mask 255.255.255.0persistence_timeout 50 protocol TCP real_server 182.148.15.233 80 {weight 3 TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 182.148.15.238 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}virtual_server 182.148.15.235 80 {delay_loop 6 lb_algo wrrlb_kind DR#nat_mask 255.255.255.0persistence_timeout 50 protocol TCP real_server 182.148.15.233 80 {weight 3 TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 182.148.15.238 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}LVS_Keepalived_Backup机器上的Keepalived.conf配置[root@LVS_Keepalived_Backup ~]# vim /etc/keepalived/keepalived.conf! Configuration File for keepalivedglobal_defs {router_id LVS_Backup}vrrp_instance VI_1 {state Backup interface eth0 virtual_router_id 51priority 90 advert_int 1 authentication {auth_type PASS auth_pass 1111 }virtual_ipaddress {182.148.15.239 }}vrrp_instance VI_2 {state Masterinterface eth0virtual_router_id 52 priority 100 advert_int 1 authentication {auth_type PASSauth_pass 1111}virtual_ipaddress {182.148.15.235 }}virtual_server 182.148.15.239 80 {delay_loop 6 lb_algo wrrlb_kind DR#nat_mask 255.255.255.0persistence_timeout 50 protocol TCP real_server 182.148.15.233 80 {weight 3 TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 182.148.15.238 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}virtual_server 182.148.15.235 80 {delay_loop 6 lb_algo wrrlb_kind DR#nat_mask 255.255.255.0persistence_timeout 50 protocol TCP real_server 182.148.15.233 80 {weight 3 TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 182.148.15.238 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}其他验证操作和上面主从模式一样~~~
